User manual UNIVERSAL REMOTE CONTROL UR5L-8500L

[. . . ] STEP5 Once you have found the correct 3-digit code, save it by pressing the same [COMPONENT] button one more time. The Component LED light will blink twice to confirm that the code was successfully stored. Now, program the rest of your Components by repeating STEPS 1-5 *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the Auto-Search Method as explained in Section B. STEP2 Line up the CLIKRTM-5 to the other remote, head-to-head, 1 or 2 inches apart. STEP3 Press any button on the CLIKRTM-5 that you want to teach a command to. [. . . ] Programming Volume Control You can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component mode. Default volume control settings on the remote control are as follows: CBL : TV DVD : TV T V : TV AUX : AUX VCR : TV D. Erasing a Single Learned Command STEP1 Press the [COMPONENT] and [ # ] buttons simultaneously for 3 seconds until the Component LED light turns on. STEP3 To exit, press and hold both the [COMPONENT] and [ # ] buttons simultaneously until the Component LED blinks 3 times. B. Auto-Search Method STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote. STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote toward the Component and press the [CH ] or [CH ] button one step at a time or keep it pressed. If any of the functions do not work as they should, repeat from STEP 3 using [CH ] or [CH ] buttons to find the correct code. Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method. If you can't find the right code using the Auto-Search Method, try the Learning Method in Section C. If you wish to store the CBL volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [OK/SEL] button simultaneously for 3 seconds. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps but press [TV] in STEP3 . K. Programming a `Macro' or Favorite Channel In CBL mode, the M1, M2 and HELP buttons can be programmed to act as a `Macro' or Favorite Channel button. STEP2 Press the M1, M2 or HELP button and [OK/SEL] button simultaneously for 3 seconds. STEP4 Press the [CH ] button to store the commands that were selected. The [CBL] Component LED will blink twice to confirm the storage of commands. H. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. The [CBL] button will blink twice to confirm the commands have been saved. E. [. . . ] Programming Channel Control You can program the channel controls (Channel Up, Channel Down and Last) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD : DVD T V : CBL AUX : AUX VCR : CBL M. Memory Lock System This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control. N. Record Your Component Set-up Codes TV VCR DVD AUX Set-up Code Number: Set-up Code Number: Set-up Code Number: Set-up Code Number: A. [. . . ]