User manual US ROBOTICS USR8054 QUICK START

[. . . ] Wireless Turbo Access Point & Router Quick Installation Guide Package Contents: -Wireless Turbo Access Point & Router -Quick Installation Guide -5VDC power supply -two (2) detachable antennas -Installation CD-ROM -one (1) Ethernet cable Before You Begin Note: Your product number is USR8054. It is important that you have your serial number written down before you install the Wireless Turbo Access Point & Router. You can find your serial number on the bottom label of the Wireless Turbo Access Point & Router and on the side of the package. If you ever need to call our Technical Support department, you will need this number to receive assistance. To make an Ethernet connection: Connect one end of the supplied Ethernet cable to your computer's Ethernet adapter. [. . . ] Many of the most common difficulties users experience have been addressed in the FAQ and Troubleshooting Web pages for your specific product. Robotics products can also be answered by technical support specialists. Country United States Canada Voice (801) 401-1143 (801) 401-1143 Online http://www. usr. com/emailsupport http://www. usr. com/emailsupport Support Hours 9:00 A. M. - 5:00 P. M. , Monday - Friday CST For current support contact information, go to the following Web site: http://www. usr. com/support Regulatory Approvals FCC Declaration of Conformity This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may causeundesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If this equipment is not installed and used in accordance with the manufacturer's instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. The manufacturer reserves the right to make changes to the content of this document and/or the products associated with it at any time without obligation to notify any person or organization of such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages. I am unable to connect to the wireless function of the Wireless Turbo Access Point & Router ireless Point Router outer. Possible Solution: Be certain that you have each Wireless PC Card set to Infrastructure mode. If your Wireless PC Cards or PCI Adapters are set to 802. 11g AdHoc mode, you will not be able to use the wireless function. Refer to the User Guide on the Installation CD-ROM for your Wireless PC Card to determine how to change this setting. Note: 802. 11g Ad-Hoc mode is used for peer-to-peer network configurations. Infrastructure mode is used to add an Access Point to the network configuration. My computer does not recognise the wireless function of the W ireless Turbo Access Point & Router after I ireless Point Router changed the settings. Possible Solution: Ensure that you are contacting the correct Wireless Turbo Access Point & Router by verifying the correct MAC address. Ensure that the correct passphrase and encryption option are being used. If you changed the settings in the configuration of the Wireless Turbo Access Point & Router, you must also change the settings of every Wireless PC Card or PCI Adapter attached to this network. [. . . ] 4. 6 Once a CUSTOMER return has been unpacked, visually inspected, and tested U. S. ROBOTICS will, at its sole discretion, repair or replace, using new or reconditioned product or parts, to whatever extent it deems necessary to restore the product or part to operating condition. ROBOTICS will make reasonable effort to ship repaired or replaced product or part to CUSTOMER, at U. S. ROBOTICS receives the authorized CUSTOMER return at an authorised U. S. [. . . ]