User manual VIEWSONIC PJD2121

[. . . ] ViewSonic SVGA DLP Projector ® - User Guide - Guide de l'utilisateur - Bedienungsanleitung - Guía del usuario - - () - () PJD2121 Model No. : VS12617 Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] You can use one of the picture modes (except the User) as a starting point and customize the settings 1. Press MENU to open the On-Screen Display (OSD) menu Go to the PICTURE > Image menu and press Enter. to select a sub-menu item to be changed and adjust the value with . This function is only available when User mode is selected up in the Picture Mode sub-menu item. Fine-tuning the image quality in user modes Adjusting color 1. Press to select a sub-menu item to be changed and adjust the value with Please be noticed this is one of the colors. Hiding the image In order to draw the audience's full attention to the presenter, you can use BLANK on the remote control to hide the screen. Press again to restore. 14 ViewSonic PJD2121 Shutting down the projector Press POWER and a confirmation message displays prompting you. If you don't respond in a few seconds, the message will disappear. The POWER indicator light flashes RED, the projection lamp shuts down, and the fans will continue to run for approximately 60 seconds to cool down the projector. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. I 15 ViewSonic PJD2121 Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Options 1. About 16 ViewSonic PJD2121 Description of each menu Feature Blank Screen Keystone Description Allows you to select which logo screen will display during projector start-up. min N/A -30 Max N/A +30 Default ViewSonic 0° Aspect Ratio Magnify Mode Vertical Keystone function by using DDP2230 of "TI" chip to provide vertical keystone correction Aspect Ratio allows the user to set the aspect ratio of the image displayed on the projector. This is helpful when the input resolution is not at the native resolution of the content or if the user wishes to fill the projector. When Picture mode is selected on User mode, this function can be active. When Picture mode is selected on User mode, this function can be active. Adjusts the degree of difference between the dark and light in the image. When Picture mode is selected on User mode, this function can be active. (At higher values, will switch to Detail Enhancement) User can set different Color Space such as Auto, RGB, YCbCr and YPbPr. Refer to Page 16, "Fine-tuning the image quality in user modes" Shows the input source. Shows the current lamp using hours. N/A N/A Fill 0 N/A 100 N/A 0 PC: VGA Component: Video Brightness -100 100 0 Contrast -50 50 0 Sharpness 0 31 16 Color Space Noise Reduction Lamp Reset Factory Reset HSG Active Source Resolution Lamp Hours N/A ON NA NA NA NA NA NA N/A OFF Automatic ON NA NA NA NA NA NA NA NA NA NA NA NA The following setup value will be changed after calibration. Phase Tracking Horizontal Position Vertical Position Adjusts the clock phase to reduce image distortion. Adjusts the image size to fit the screen Adjusts the horizontal width of the image. Adjusts the Vertical width of the image. 17 ViewSonic PJD2121 Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. [. . . ] You will need to provide your product's serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim. For Your Records Product Name: _______________________________ Model Number: _______________________________ Document Number: ___________________________ Serial Number: ________________________________ Purchase Date: _______________________________ Extended Warranty Purchase?To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. [. . . ]