User manual WHIRLPOOL PGS 300/IX PROGRAM CHART

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL PGS 300/IX. We hope that this WHIRLPOOL PGS 300/IX user guide will be useful to you.


WHIRLPOOL PGS 300/IX PROGRAM CHART: Download the complete user guide (1271 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL PGS 300/IX KURZANLEITUNG (1238 ko)
   WHIRLPOOL PGS 300/IX TABLEAU DE PROGRAMMES (1280 ko)
   WHIRLPOOL PGS 300/IX PRODUCT-INFORMATIEBLAD (1237 ko)

Manual abstract: user guide WHIRLPOOL PGS 300/IXPROGRAM CHART

Detailed instructions for use are in the User's Guide.

[. . . ] - Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer’s instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the user manual. TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 60 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel, that has to close completely the cutout in order to avoid any contact with the bottom part of the hob, must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. [. . . ] • After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position position to check flame stability. to minimum (Apply the label from warranty here) 5019 619 01517 Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY ELECTRICAL CONNECTION WARNING WARNING This operation must be performed by a qualified technician. • • • The electrical connections must comply with local regulations. L Earth (yellow/green) N REPLACING THE INJECTORS (see the injector table in the Instruction) • • • Remove grids (A). Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to be replaced. • If you have a multiple crown burner use side spanner to replace the injector (E). Before installing the hob, remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration. IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows: • tighten screw to reduce the flame height (-); • loosen screw to increase the flame height (+). The adjustment must be performed with the tap in minimum gas setting position (small flame) . • At this stage, light up the burners and turn the knobs from max position to minimum position to check flame stability. Upon completion of adjustment, reseal using sealing wax or an equivalent material. Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. NOTE: the power supply cable must be long enough to permit its upward extraction. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures). Top 30-60 mm Top 20 mm FR REFERENCE TO LOCAL REGULATIONS The installation and maintenance of the appliance must be carried out by a qualified skilled technician in accordance with the regulations in force, and in particular: • Decree of 2 August 1977 Technical and Safety Rules applicable to fuel gas and liquefied hydrocarbon installations located within residential buildings and outbuildings. • Departmental Health Regulations For appliances connected to the mains electricity supply. • Standard NF C 15-100 Low-voltage electrical installations - Standards. ADJUSTMENT TO DIFFERENT TYPES OF GAS WARNING This operation must be performed by a qualified technician. If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. • The gas nozzles must be changed by After Sales Service or a qualified technician. • Nozzles not supplied with the appliance must be ordered from After Sales Service. NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go. [. . . ] fish kettle). INJECTORS TABLE Burner Rapid Semi-rapid Auxiliary CATEGORY II2E+3+ Injector marking Rated thermal Rated flow rate consumption kW Rapid Y 115 Z 95 X 72 Y 115 Z 95 X 72 85 63 50 85 63 50 3. 00 1. 65 1. 00 3. 00 1. 65 1. 00 3. 00 1. 65 1. 00 3. 00 1. 65 1. 00 286 l/h 157 l/h 95 l/h 332 l/h 183 l/h 111 l/h 218 g/h 120 g/h 73 g/h 214 g/h 118 g/h 71 g/h Pot Ø From 24 to 26 cm From 16 to 22 cm From 8 to 14 cm Type of gas used Type of burner Reduced heat capacity kW BE 0. 80 0. 45 0. 35 0. 60 0. 35 0. 30 0. 60 0. 35 0. 30 0. 60 0. 35 0. 30 Gas pressure mbar min. max. FR 0. 60 0. 35 0. 30 NATURAL GAS (Methane) G20 Semi-rapid Auxiliary Rapid 17 20 25 NATURAL GAS (Methane) G25 LIQUEFIED PETROLEUM GAS (Butane) G30 LIQUEFIED PETROLEUM GAS (Propane) G31 Semi-rapid Auxiliary Rapid Semi-rapid Auxiliary Rapid Semi-rapid Auxiliary 20 25 30 HOW TO USE THE HOB WARNING Do not let the burner flame extend beyond the edge of the pan. 20 28-30 35 IMPORTANT: WHEN THE HOB IS IN USE, THE ENTIRE HOB AREA MAY BECOME HOT. • To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting. • After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL PGS 300/IX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL PGS 300/IX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.