User manual WHIRLPOOL WGD7300DW INSTALLATION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WGD7300DW. We hope that this WHIRLPOOL WGD7300DW user guide will be useful to you.


WHIRLPOOL WGD7300DW INSTALLATION GUIDE: Download the complete user guide (10965 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WGD7300DW USE & CARE GUIDE (4515 ko)
   WHIRLPOOL WGD7300DW INSTRUCTION SHEET (795 ko)
   WHIRLPOOL WGD7300DW INSTRUCTION SHEET (795 ko)
   WHIRLPOOL WGD7300DW WARRANTY INFORMATION (143 ko)
   WHIRLPOOL WGD7300DW DIMENSION GUIDE (320 ko)
   WHIRLPOOL WGD7300DW USE & CARE GUIDE (4515 ko)
   WHIRLPOOL WGD7300DW INSTRUCTION SHEET (795 ko)
   WHIRLPOOL WGD7300DW WARRANTY INFORMATION (143 ko)
   WHIRLPOOL WGD7300DW QUICK REFERENCE SHEET (851 ko)
   WHIRLPOOL WGD7300DW VENTILATION SPECIFICATION (1518 ko)

Manual abstract: user guide WHIRLPOOL WGD7300DWINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] INSTALLATION NOTES Date of purchase:__________________________________ Date of installation:________________________________ Installer:_________________________________________ Model number:____________________________________ Serial number:____________________________________ NOTES CONCERNANT L’INSTALLATION Date d’achat :______________________________________ Date d’installation :_________________________________ Installateur :_______________________________________ Numéro de modèle :_________________________________ Numéro de série :___________________________________ W10680136B W10680137B-SP 1 DRYER SAFETY 2 3 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Tools needed for gas installations: Tools needed for all installations: 8" (203 mm) or 10" (254 mm) pipe wrench Flat-blade screwdriver #2 Phillips screwdriver 8" (203 mm) or 10" (254 mm) adjustable wrench (for gas connections) Pipe-joint compound resistant to LP gas 1/4" nut driver or socket wrench (recommended) Tin snips (new vent installations) Parts supplied (all models): Tape measure Vent clamps Leveling legs (4) Parts supplied (steam models): Level Pliers “Y” connector Short inlet hose Rubber washer Parts package is located in dryer drum. Parts needed (steam models): Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Caulking gun and compound (for installing new exhaust vent) 5' (1. 52 m) inlet hose If using a power supply cord: Utility knife Putty knife Use a UL listed power supply cord kit marked for use with clothes dryers. [. . . ] Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to steps 1-2 on page 12 for power supply cord strain relief: then steps 3-6 for 4-wire Power Supply Cord Connection section. Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to steps 1-2 on page 13 for power supply cord strain relief: then steps 3-5 for 3-wire Power Supply Cord Connection section. 4-wire direct connection: Go to steps 1-2 on page 14 for direct wire strain relief: then steps 3-8 for 4-wire Direct Wire Connection section. 3-wire direct connection: Go to steps 1-2 on page 15 for direct wire strain relief: then steps 3-7 for 3-wire Direct Wire Connection section. Remove terminal block cover BE C F D A Before you start, disconnect power. Hole below terminal block cover NOTE: If local codes do not permit connection of a cabinet-ground conductor to neutral wire, go to “Optional 3-wire Connection” section. This connection may be used with either a power supply cord or a direct wire connection. E A B Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole (B) below the terminal block opening so that one tab is pointing up (A) and the other is pointing down (D), and hold in place. Tighten strain relief screws just enough to hold the two clamp sections (C) together. Remove neutral ground wire (E) from external ground conductor screw (A). Attach power supply cord to strain relief Connect neutral ground wire and neutral wire E C B Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Connect neutral ground wire (E) and neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Connect ground wire F 4-wire Power Supply Cord Connection IMPORTANT: A 4-wire connection is required for mobile A. Homes and where local codes do not permit the use of 3-wire connections. Ring terminals Connect ground wire (F) (green or bare) of power supply cord to external ground conductor screw (A). Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Remove center screw Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole (B) below the terminal block opening. [. . . ] Q Check for leaks around “Y” connector, faucet, and hoses. Q If you live in a hard water area, use of a water softener is Place towel on top of dryer to avoid damaging the surface. Recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system, which will reduce product performance. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WGD7300DW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WGD7300DW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.