User manual WHIRLPOOL WRS322FDAD USE & CARE GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WRS322FDAD. We hope that this WHIRLPOOL WRS322FDAD user guide will be useful to you.


WHIRLPOOL WRS322FDAD USE & CARE GUIDE: Download the complete user guide (1362 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WRS322FDAD ENERGY GUIDE (403 ko)
   WHIRLPOOL WRS322FDAD DIMENSION GUIDE (88 ko)
   WHIRLPOOL WRS322FDAD INSTALLATION GUIDE (793 ko)
   WHIRLPOOL WRS322FDAD WARRANTY INFORMATION (85 ko)

Manual abstract: user guide WHIRLPOOL WRS322FDADUSE & CARE GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. Note: Unit can NOT be installed behind a closed cabinet door. Product Dimensions 24" Including Handle 28-1/2" Cut-Out Dimensions Filler Panel (Not Provided by U-Line) ­ May Be Added Above or Below Unit to Enclose for a Built-In Look 20-13/16" Figure 2 Door Swing/Clearances Information Typical Counter Height 34-1/4" to 35-1/8" Cut-Out Height 28-5/8" to 28-7/8" See Electrical Specifications for Power Supply 24" Minimum Units have a zero clearance for the door to open 90° (see Figure 3). U-Line recommends a minimum door clearance of 1/4" to accommodate the handle if the unit is right-hand hinged and installed next to a wall or similar type of structure. [. . . ] Note that there may be a nut behind one or both screws on either side. Figure 3 Figure 6 Figure 7 4. Align hinge outer edge with cabinet before tightening screws. 02/2005 5 www. U-LineService. com CO29A and CO29FF Ice Maker/Refrigerators 5. Relocate plastic spacer/ bushing on bottom of door to opposite side, and place door on bottom hinge pin. Clean out bushing hole in door bottom with a screwdriver if necessary. Remove plastic hole plug from door handle and relocate on opposite side. Replace three plastic plugs removed in Step 8 into holes on top of unit. Replace screws in holes in bottom of unit on opposite side. Figure 8 Figure 11 Hinge Other Site Requirements Power Supply Plastic Plug Hole Plastic Plug Hole The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 9. Screw Right Side Door Swing Right Side Hinge Invert Screw Invert Hinge Left Side Door Swing Water Supply The unit requires a 1/4-inch OD water supply line and a shut-off valve. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. Remove three plastic screw plugs from hinge holes, top of cabinet, opposite side. Invert and install upper hinge on door. Environmental Requirements The surrounding air temperature must be at least 50°F (10°C) but must not exceed 110°F (40°C). Figure 15 www. U-LineService. com 8 02/2005 CO29A and CO29FF Ice Maker/Refrigerators 7 Prepare Power Supply Electrical Specifications CAUTION Water Connection Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). An individual, properly grounded branch circuit or circuit breaker is recommended. GFCI (ground fault circuit interrupter) is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping. See Figure 19 for recommended receptacle location. Figure 16 Figure 17 2. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. It is located toward the top of the middle recessed section of the grille. Place the two hook-hinges (located on the rear bottom side of the grille) onto the front lip of the unit base. Swing the grille up into position, aligning the grille screw hole on the grille to the grille screw hole on the cabinet. See Figure 22. www. U-LineService. com 10 02/2005 CO29A and CO29FF Ice Maker/Refrigerators 10 Start-Up for the First Time Grille Hook-Hinge Unit Base Front Lip Initial Start-Up The unit is shipped with the control preset to a mid-point setting between 4 and 5. [. . . ] While the bin arm is locked, the unit will maintain temperature for ice storage. Hook-Hinge Figure 22 5. Slide the shelves onto lower sets of ribs, making sure the decorative graphics are on the underside of the shelves. While edge strips go toward the rear and silver edge strips go toward the front. See Figure 23. IMPORTANT It is possible that dirt or scale will dislodge in the water line. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WRS322FDAD




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WRS322FDAD will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.