User manual XEROX PHASER 1235

[. . . ] P H A S E R® 1 2 3 5 COLOR PRINTER User Guide Phaser® 1235 Color Printer User Guide 071-0730-00 June 2000 Copyright © Xerox Corporation. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Xerox Corporation. Phaser®, PhaserShare®, ColorStix®, the TekColor® icon, Made For Each Other®, DocuPrint®, WorkSet®, Ethernet®, the stylized X, and XEROX® are registered trademarks of Xerox Corporation. [. . . ] The Face-down output bin on top of the printer holds up to 500 sheets and the Face-up output bin at the rear of the printer holds up to 100 sheets of 75 g/m2 (20 lb. ) bond paper. Pull out the Universal Tray. Trays 0730-25 2. Fan the media to release sheets that are stuck together. 0730-26 22 Phaser 1235 Color Printer 3. Adjust the width and length guides to match the size of your paper. Paper size is automatically detected from the tray settings. 0730-27 4. Observe the fill line on the left side of the Universal Tray. Do not load paper or transparencies above this line because you may damage the printer. bond paper) Transparency: 175 Standard sheets; 175 Premium sheets Trays 0730-28 Note: To load transparencies: From the Tray 1 Type menu, select Transparency. Select the Transparency setting and tray in the printer driver. User Guide 23 5. Insert a stack of paper into the Universal Tray. For proper print orientation: s s The print side should be face-down. Letterhead should be at the front of the tray. s 0730-29 s Trays For information on loading transparencies, refer to the instructions shipped in the Xerox Phaser 35 Series Transparency Film box. 6. Press the Item buttons to scroll to Tray 1 Type (if loading Tray 1). c. Press the Value buttons to select an option listed: Front Panel Media Options Media Type Plain Preprinted Letterhead Weight 60-90 g/m2 (16-24 lb. bond) 24 Phaser 1235 Color Printer Front Panel Media Options (Continued) Media Type Transparency Prepunched Bond Recycled Color Card Stock Light Card Stock 60-90 g/m2 (16-24 lb. Press the On-line button to exit the Menu. To avoid possible print-quality and media-feed problems, make sure that the loaded media matches the tray type setting. Trays User Guide 25 Multi-Sheet Bypass Feeder (MBF) Always use the Multi-Sheet Bypass Feeder (MBF) for specialty media. Media Specifics s s 60 - 203 g/m2 (16 - 54 lb. The MBF supports the following paper and specialty media types: Supported Media Paper 60 - 90 g/m2 (16 - 24 lb. bond) Xerox Phaser 35 Series Transparencies Xerox Phaser Glossy Coated Paper 150 g/m2 (100 lb. bond) 80 sheets (Standard) 70 sheets (Premium) 80 sheets 30 sheets 30 sheets g/m2 (45-75 lb. cover) Cover Stock 121 - 203 Index Stock 121 - 203 g/m2 (67-112 lb. book) 50 sheets 10 envelopes Multi-Sheet Bypass Feeder 121 - 203 g/m2 (74-125 lb. tag) Xerox Phaser Color Laser Labels Envelopes (Monarch, #10, C5, DL, JIS B5) s For information on loading transparencies, refer to the instructions shipped in the Xerox Phaser 35 Series Transparency Film box. When sending a Manual Feed job to the MBF, all media must be removed and replaced each time so that the MBF registers paper for the current print job. s 26 Phaser 1235 Color Printer s When sending a Multi-Sheet Bypass Feeder (MBF) job from the driver, the printer prompts you to load the correct media if the media does not match what you previously loaded. If a different media size is loaded in the MBF than what is selected in the driver, the printer stops and the front panel prompts you to load the correct media size in the MBF. s Loading the Multi-Sheet Bypass Feeder (MBF) 1. Open the Multi-Sheet Bypass Feeder tray and unfold the single extension (a). Open the Face-up output bin at the rear of the printer and swing out the two extensions where the media will exit (b). a b Multi-Sheet Bypass Feeder 0730-30 s The Multi-Sheet Bypass Feeder (MBF) does not automatically detect paper size. [. . . ] SECTION 4 ­ FIRST AID MEASURES EYE CONTACT: Flush with water for 15 minutes, including under eyelids. INGESTION: In the unlikely event of ingestion of a wiper, first aid measures should focus on removal of the object and preventing choking. Call physician immediately. Specifications SECTION 5 ­ FIRE-FIGHTING MEASURES FLASH POINT (TCC): 56 degrees F FLAMMABLE LIMITS (PERCENT BY VOLUME): LEL: NA UEL: NA AUTOIGNITION TEMPERATURE degrees F (degrees C): NA EXTINGUISHING MEDIA: Isopropyl-alcohol fires may be extinguished using carbon dioxide, dry chemical or alcohol foam. UNUSUAL FIRE OR EXPLOSION HAZARDS: Isopropyl alcohol may release vapors which may ignite at or above flash point. [. . . ]