User manual XEROX PHASER 5550

[. . . ] Phaser® 5550 printer User Guide Guide d'utilisation Guida dell'utente Benutzerhandbuch Guía del usuario Guia do Usuário Gebruikershandleiding Användarhandbok Betjeningsvejledning www. xerox. com/support Copyright © 2008 Xerox Corporation. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Xerox Corporation. Copyright protection claimed includes all forms of matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as styles, templates, icons, screen displays, looks, etc. [. . . ] Do not load transparencies above the fill line; it may cause the printer to jam. Handle transparencies by the edges using both hands to avoid fingerprints and creases which can cause poor print quality. Use Xerox Transparencies; print quality may vary with other transparencies. Printing Transparencies from Tray 1 (MPT) or Tray 6 1. Fan the transparencies to release sheets that may stick together. 5550-170 Phaser® 5550 Printer 4-35 Printing on Specialty Media 2. Insert the transparencies long-edge feed into Tray 1 (MPT) or Tray 6. MAX 5550-118 5550-142 Tray 1 (MPT) Long-Edge Feed Tray 6 Long-Edge Feed Note: Do not load paper above the fill line inside the tray. Adjust the paper guides to the size of the transparencies if necessary. If prompted on the control panel, press the OK button to accept the paper size and type that are shown. Select the paper size, and then press the OK button to save your selection. In the printer driver, select either Transparency as the paper type or the tray you loaded as the paper source. Printing Transparencies from Trays 2-5 1. Fan the transparencies to release sheets that may stick together. 5550-170 Phaser® 5550 Printer 4-36 Printing on Specialty Media 2. Insert the transparencies (long-edge feed preferred) into Tray 2, 3, 4, or 5. 5550-143 Note: Do not load paper above the fill line inside the tray. If prompted on the control panel, press the OK button to accept the paper size and type that are shown. Select the paper size, and then press the OK button to save your selection. In the printer driver, select either Transparency as the paper type or the tray you loaded as the paper source. Phaser® 5550 Printer 4-37 Printing on Specialty Media Printing Envelopes This topic includes: Guidelines for Envelopes on page 4-38 Printing Envelopes from Tray 1 (MPT) on page 4-39 Printing Envelopes from the Optional Envelope Tray on page 4-40 Guidelines for Envelopes Buying and Storing Envelopes Use only paper envelopes specified in the Supported Papers table. Successful envelope printing is highly dependent on the quality and construction of the envelopes. It is recommended that you maintain constant temperatures and relative humidity. Store unused envelopes in their packaging to avoid the effects of moisture and dryness which can affect print quality and cause wrinkling. Excessive moisture can cause the envelopes to seal before or during printing. Avoid padded envelopes; purchase envelopes that lie flat on a surface. Remove air "bubbles" from the envelopes before loading by setting a heavy book on top of the envelopes. If wrinkling or embossing problems occur, use a different brand of envelopes made specifically for laser printers. For more information, go to Supported Paper and Media on page 4-2. Preparing to Print Follow these guidelines to prevent wrinkling problems: Print only on the front of the envelope. [. . . ] This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with these instructions, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiver. [. . . ]