User manual XEROX PHASER 750

[. . . ] PHASER 750 COLOR PRINTER ® User Guide ® www. tek. com/Color_Printers/ Phaser® 750 Color Printer User Guide 071-0632-00 December 1999 Copyright © Tektronix, Inc. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Tektronix, Inc. Tektronix®, Phaser®, PhaserShare®, ColorStix®, the TekColor® icon, and Made For Each Other® are registered trademarks of Tektronix, Inc. [. . . ] (3. 6 mm) 1 2 3 4 5 0632-57 12 Phaser 750 Color Printer Paper and Transparency Trays Paper Tray R PE PA A4 PAPER A/Letter PAPER A4 PAPER Legal 0632-01 s s s 250-sheet capacity 60 - 90 g/m2 (16 - 24 lb. ) Use Tektronix Premium Color Printing Paper or Premium Laser Bond Paper for best results. Do not load transparencies. s Note Load only laser paper in the paper trays. Specialty papers such as Tektronix Glossy Coated Paper, Tektronix Premium Cover Paper, envelopes, and Tektronix Laser Labels must be loaded in the Multi-Purpose Tray. This will result in a Jam-Wrong Media error. Trays User Guide 13 Transparency Tray TR AR SP AN A4 EN CY TRANSPARENCY A/Letter TRANSPARENCY A4 0632-02 s Use only Tektronix transparencies. For information on Tektronix transparencies, visit the Tektronix web site: www. tek. com/Color_Printers/products/supplies/trans/index. html Install the transparency tray only in the printer's upper or middle tray slots. If this tray is installed in the lower tray slot, a front panel error occurs that stops the print job. The transparency tray must then be moved to the upper or middle tray slot. s Caution Use of non-Tektronix transparencies can damage printer components or produce poor image quality. Trays Do not load paper in the Transparency tray, this will result in a Jam-Wrong Media error. s Tektronix transparencies s Use only Premium or Standard Tektronix transparencies (see page 1 for supplies ordering information) 100-sheet capacity s 14 Phaser 750 Color Printer Loading Paper or Transparency Tray Note Place the side to be printed (for example, letterhead paper) face-down under the hooks. Push down on the tray's metal plate until it clicks, locking it in place. R PE PA A4 0632-08 2. Fan the media to release sheets that are stuck together. 0632-09 User Guide 15 3. Place the media in the tray under the hooks. Caution Keep the media level below the indicator on the tray's label; otherwise, the printer may jam or be damaged. s Letterhead: Load this material face-down under the tray hooks. Transparencies: Place the Tektronix logo strip face-up under the transparency tray hooks. Use Tektronix transparencies only. s MAXIMUM TRAY LEVEL TR AN AR SP 4 A EN CY 0632-10 4. Tray capacity: a. Paper tray 250 sheets Transparency tray 100 sheets For tray placement guidelines, see page 10. 5. Insert the tray. s 16 Phaser 750 Color Printer Multi-Purpose Tray Overview Always use the Multi-Purpose Tray for speciality media; it supports the following media types: Supported Media Paper and Paper 2nd Side 75-105 g/m2, (20-28 lb. ) Tektronix Transparency Film Tektronix Glossy Coated Paper Heavy paper: s Multi-Purpose Tray Tray capacity 100 sheets 50 sheets 30 sheets 30 sheets Media thickness switch Thin Normal Normal Thick Cover Stock s 120-163 g/m2), (40- 60 lb. ) 120-163 g/m2, (60- 90 lb. ) 120-163 g/m2, (32- 40 lb. ) 30 sheets 10 envelopes Thick Thick s Index Stock s s Card Stock s Tektronix Color Laser Labels #10 Envelopes User Guide 17 Note For the best coverage when using laser paper heavier than 105 g/m2 (28 lb. ) in the Multi-Purpose Tray, select Heavy Paper as the media type. If the printer experiences frequent media jams at the Multi-Purpose Tray, move the Media Thickness Switch to a thicker setting. If the printer experiences frequent double-feed errors at the Multi-Purpose Tray, move the Media Thickness Switch to a thinner setting. Multi-Purpose Tray Thin Normal Thick 33100-68 Note The printer prompts you for the paper type and size. If the wrong media is selected, the printer's front panel displays a Jam-Wrong Media message. 18 Phaser 750 Color Printer Loading the Multi-Purpose Tray 1. Pull out the slide and adjust the guides for the width of the media. 0632-11 2. Adjust the Media Thickness switch for the media you are using (see page 17). Thin Normal Thick 33100-68 User Guide 19 3. Insert the media: s For Tektronix Transparencies place the Tektronix strip facing down and refer to page 23. For letterhead, place face-up and refer to page 11. s s s 0632-63 4. The front panel prompts you to select the media type and then the media size: Tektronix Transparency Tek Transparency OK Letter OK 0632-44 or A4 20 Phaser 750 Color Printer Tektronix Glossy Coated Paper Tek Glossy Coated Paper OK Letter OK 0632-45 or A4 Tektronix Premium Cover Paper Heavy Paper OK Letter OK 0632-64 or A4 Tektronix Color Laser Label Tek Labels OK Letter OK 0632-47 or A4 Paper s s s Letterhead Office Laser Paper Standard paper and letterhead 75 - 105 g/m2 (20 - 28 lb. ) Paper OK Letter OK Legal, A4, or Executive 0632-48 User Guide 21 Paper 2nd Side s Standard paper and letterhead 75 - 105 g/m2 (20 - 28 lb. ) Paper-2nd Side OK Letter OK Legal, A4, or Executive 0632-49 Heavy Paper s s s Cover Stock 120-163 g/m2 (60 lb. ) Index Stock 120-163 g/m2 (90 lb. ) Card Stock 120-163 g/m2 (40 lb. ) Heavy Paper OK Letter OK Legal, A4, or Executive 0632-50 Envelope #10 Envelope OK # 10 OK 0632-51 5. In the Print screen (using a supported driver), select Multi-Purpose Tray. Send the job to the printer. 22 Phaser 750 Color Printer Loading Special Media Tektronix Transparencies 1. Set the Media Thickness Switch to Normal. Thin Normal Thick 33100-68 2. 3. Adjust the tray's guides for the width of your Tektronix Transparencies. Insert the transparency with the logo strip face-down, entering the printer first. Special Media 0632-16 User Guide 23 4. Fill the Multi-Purpose Tray to the level indicator on the guide (maximum capacity is 50 sheets). 4 3 0236-13 Special Media 5. At the front panel's media type prompt, scroll to Tek Transparency and press OK. Scroll to the media size Letter or A4. Tek Transparency OK Letter OK 0632-44 or A4 6. In the application's Print screen under Tray Selection or Paper Source, depending on the driver, select the Multi-Purpose Tray and send the job to the printer. 24 Phaser 750 Color Printer Printing #10 Envelopes 1. [. . . ] If printing from the Multi-Purpose Tray, make sure that the correct media type is selected from the front panel. Open the left side door, remove the jammed media. See Jam at A illustrations. User Guide 47 Jam at A Solution 1 Open the left side door; remove the jammed media. Jams 33100-08 Solution 2 Remove the media tray; remove the jammed media from inside the printer. 33100-09 48 Phaser 750 Color Printer Jam at B (Lower Tray Assembly Only) Solution 1 Open the lower left side door and remove the jammed media. 33100-10 Solution 2 Remove the selected media tray (middle or lower tray) and remove the jammed media from inside the printer. tte Le A/Paper r tte Le A/Paper r 33100-11 User Guide 49 Jam at C Caution The Fuser is hot. To avoid personal injury, use caution or wait for the Fuser to cool before touching it. [. . . ]