User manual ZENEC ZE-40DVBT

[. . . ] Flankensteilheit für Hochpass und Tiefpass à Einstellbereich der Frequenzweiche: 60Hz ~ 220Hz in 10Hz Schritten à Digitale Regelung der Eingangsempfindlichkeit, einstellbar von 0. 2 bis 6. 0 Vrms à Optischer Toslink & koaxialer Cinch- Digitaleingang mit drei separat wählbaren Quellen AUX1 / AUX2 / AUX3 à Zwei analoge stereo Cincheingänge für Input 1 / Input 2 à Konfiguration der Audio und Video Einstellungen per Bildschirm-Menü à Fernbedienung für Konfiguration per Bildschirm-Menü à IR-Auge mit Verlängerungskabel à Remote Ausgangsterminal für separaten SubwooferAmp 4 EINGÄNGE - AUSGÄNGE 1 2 5 7 81 9 1 0 1 34 6 1) Cinch Eingangsbuchsen (Input 1 / Input 2 - linker und rechter Kanal). NF-Signal Eingang für den Anschluss von Line-Out Cinch-Ausgängen des Steuergerätes 2) Coaxial Input für den Anschluss eines digitalen PCB / Bitstream Ausgangs vom Steuergerät. wenn für den Subkanal (oder den / die angeschlossenen Subwoofer) mehr Leistung erwünscht ist. Sämtliche Einstellungen am ZE-40DVBT Verstärker werden via Bildschirm-Menü ausgeführt! [. . . ] and thank you for purchasing this 5. 1 channel digital power amplifier from ZENEC!To maximize the performance of your complete car audio system, it is recommended that you acquaint yourself thoroughly with the capabilities and features of this amplifier. Therefore read this manual carefully, before attempting the installation of this multichannel amplifier. It is recommended to retain this manual and the purchasing/installation receipts for future reference. TECHNICAL FEATURES 5. 1-CHANNEL MULTIMEDIA DIGITAL AMPLIFIER à 50Wrms x 5 & 50Wrms x 1 @ 4 ohms (> 0. 2% THD / 13. 8V) à Max. output of subwoofer channel: 100Wrms @ 2 ohms (0. 2% THD / 13. 8V) à Satellite channels 4 ohms stable / subwoofer channel 2 ohms stable à Fullrange digital amplification circuitry à Variable input sensitivity: 0. 2 ­ 6V à Damping factor @ 4 ohms: < 100 à Signal to noise ratio: < 90dB à Channel separation: < 50dB à Dimensions WxHxD: 270 x 45 x 160mm KEY FEATURES 5. 1 channel class-D fullrange amplifier with integrated AV-processor and OSD Dolby Digital decoding format à DD 5. 1 DTS decoding format à DTS 5. 1 Listening mode selection ( 2-CH Stereo / Phantom Mode / Matrix Surround Mode Integrated DSP based crossover with 24dB/oct slopes (60Hz ~ 220Hz adjustable in 10Hz steps) Input sensitivity control (adjustment range 0. 2/0. 5/1. 0/1. 5/2. 0/2. 5/3. 0/3. 5/4. 0/4. 5/5. 0/5. 5/6. 0 Vrms) System setup by on-screen display Optical & coaxial digital anlog RCA inputs Test tone mode for speaker setup and calibrtion Remote control for OSD adjustment Remote output terminal 16 INPUTS ­ OUTPUTS 1 2 5 7 81 9 1 0 1 34 6 1) RCA inputs (Input 1/Input 2): Line inputs for connection with the RCA line-outs of the headunit 2) Digital coaxial RCA input: For connection of the ZE-40DVBT amplifier to the digital output (Bitstream, / PCM) of a DVD headunit. 3) Subwoofer output: Sends a subwoofer pre-amp signal to a larger subwoofer amplifier if necessary. 4) Video Input/Output: The ZE-40DVBT provides function selection and display exclusively by OSD (On-Screen Display). For this purpose, the video output from a DVD or other video source is connected into the video input of the amplifier. The video output should then be connected to the input of the monitor, LCD, or TV. When video input into the system is absent, the display color is blue and display position may be altered. This allows selection and display of functions even when no video sources are playing. As soon as the value is changed, the new value is displayed without requirement of confirmation. For value changes, the left button is used for decreasing values, and the right button is used for increasing values. 18 7. Enter This button is used to enter the channel level control in the Set-Up menu. Source Display By pushing this button, you can display the decoding mode or Pro Logic mode on the monitor or TV. The following is an explanation of the modes: · Dolby Digital - Input source is Dolby Digital bitstream for all listening modes · Pro Logic - Input source is PCM and Pro Logic is on for phantom or surround modes. · Dolby Surround - Input source is Dolby Digital 2. 0 Stereo and Pro Logic is on for phantom and surround modes. · PCM - Input source is PCM and Pro Logic is off for all listening modes or input source is PCM and Pro Logic is on for stereo mode. When channel level menu is invoked, these buttons cannot be used for control of channel levels. SPEAKER CONNECTION SCHEMATIC 19 POWER INPUT SCHEMATIC A/V CONNECTION SCHEMATIC 20 OPERATION GUIDE 1. Input Source Selection To select the input source for the system, the system should be turned on, then: 1) Push , , INPUT" selection button on remote controller 2) Continuing to push the , , INPUT" selection button while the input is displayed on the monitor or TV makes a change in the input source as follows: OPTICAL -> COAXIAL -> INPUT1 -> INPUT2 -> OPTICAL (in circular order). If there is an error in the data received via the optical or coaxial line the display will blink continuously. [. . . ] continuously variable 60 - 220 Hz continuously variable 60 - 220 Hz 270 x 45 x 160 mm 2. 2kg 26 27 WARRANTY / GARANTIE 2 YEARS LIMITED WARRANTY Dear customer Thank you for purchasing this ZENEC product. It is advisable to keep the original packing material for any future transporting of the product. Should your ZENEC product require warranty service, please return it to the retailer from whom it was purchased or the distributor in your country. This ZENEC product is warranted against defective materials or workmanship for a period of TWO years from date of purchase at retail. [. . . ]