User manual AEG-ELECTROLUX 90S
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX 90S. We hope that this AEG-ELECTROLUX 90S user guide will be useful to you.
Manual abstract: user guide AEG-ELECTROLUX 90S
Detailed instructions for use are in the User's Guide.
[. . . ] - Do not operate where aerosol (spray) products are being used or where oxygen is being administered. - Do not put anything on the foot controller because the machine may accidentally start and the motor or the foot controller may overheat. - To disconnect turn all controls to the off position, then remove plug from outlet. - Switch the machine off when making any adjustments in the needle area, such as threading needle, changing needle or changing presser foot and the like. [. . . ] 2
2 ○
Thread between two discs
3 3 ○
Upper looper thread
Lower looper thread
2
2 ○
Lower looper
10 ○ 11 ○
Upper looper
8 7
9 ○
3
3 ○
4 8
11 ○
4 ○
8 ○
6 ○ 7 ○ 6
6 ○ 9 8 ○○ 7 ○
7 6
5 5 ○
5
5 ○
10 ○
( 10 )
NEEDLE THREADING
5. Important: The thread must lie correctly between the two discs inside the tension dials. Pull out the thread end about 10 cm (4") long from the needle eyes. Raise the presser foot and place threads under it, then lower the presser foot. 1 ○
1
2
2 ○
Left needle thread
Right needle thread
2
2 ○
5 6 7 8
6 ○ 7 ○ 8 ○ 9 ○
3 4
5 ○
3 ○ 4 ○
Thread between two discs
3 3 ○
7
8 ○
6 ○
5
6
7 ○
4
5 ○ 4 ○
9 ○
8
( 11 )
TRIAL SEWING
When the overlock has been threaded for the first time or re-threaded because of thread breakage during sewing, start sewing in the following manner. Holding the end of threads between your left finger tips, turn the handwheel slowly toward you two or three times and check the thread chain. Place fabric for trial sewing under the presser foot and start sewing slowly. Cloth
When work is finished, continue sewing to form about 5 cm (2") long thread chain from the end of fabric. ( 12 )
ADJUSTING THREAD TENSIONS
Thread tensions will vary according to the type and thickness of both thread and fabric. Adjust the thread tension of the machine accordingly while checking the seam. thread tension: Turn dial toward smaller numbers , tension becomes loose. b: Right needle thread tension dial
C: Upper looper thread tension dial
A: Left needle thread tension dial
D: Lower looper thread tension dial
Correct thread tension
Right needle thread
6 mm (0. 24”)
Back side Left needle thread
Lower looper thread Upper looper thread
( 13 )
It is necessary to adjust the thread tension for the seams shown below. [ ADJUSTING THE NEEDLE THREAD TENSIONS ]
The left needle thread tension is too loose. Back side
Back side
Front side Tighten the left needle thread tension. [ ADJUSTING THE LOOPER THREAD TENSIONS ]
The lower looper thread is tight and/or the upper looper thread is loose. The upper looper thread is tight and/or the lower looper thread is loose. Back side
Back side
Front side Loosen the lower looper thread tension and/or tighten the upper looper thread tension. Front side Loosen the upper looper thread tension and/or tighten the lower looper thread tension. ( 14 )
STITCH SELECTION AEG 760
Threading path for 4-Thread Seam Type of stitch Needle position left and right 6 mm right needle 3 left needle 4 right hook 1 left hook 2
Tension Dial: The following values are average values for medium-heavy material and normal polyester yarn red 2. 0
4-Thread Stretch Safety Seam
2-Needle 4-Thread stitch is ideal for medium to heavy stretch fabrics such as knitwear and swimwear Needle position left or right 3-Thread Overlock Seam wide and narrow 1-needle, 3-thread stitch is used for finishing of normal fabric. Depending on the selected needle position there is an overlock seam width of 4. [. . . ] The front feed teeth, therefore, holds the fabric taut to prevent puckering. ( 27 )
TROUBLE SHOOTING GUIDE
Check items below before calling for service. 19
( 28 )
CLEANING AND LUBRICATING
Warning: When cleaning the machine or changing its lamp, disconnect it from the mains. To keep your machine running smoothly ; it is necessary to clean using the brush from the accessory box now and then. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX 90S
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX 90S will begin.