User manual BECKER DTM INSTALLATION GUIDE

[. . . ] , QVLGH WKH YHKLFOH ) ) The antenna can only be installed on a non-metallised windscreen. When selecting the installation position, ensure that the antenna has a clear view of all directions, and that it is not covered by the windscreen wipers. Obstructions caused by the bonnet, window crossbeams and roof should be avoided as far as possible. Subject to correction and technical modifications 27 Copyright by Becker GmbH, D-76303 Karlsbad , QVWDOODWLRQ JXLGH a. Remove protective strip from top of adhesive tape (2) and stick to the centre of the base plate underside. [. . . ] Move the vehicle several metres forwards or backwards for the speed signal function test. 7, , + 09, *;065 P $!P VVV P ) The number under 7, , + must change (even at a low speed). The number under 7, , + should not increase when idling or pressing the accelerator when the vehicle is parked. P VMN P Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad , QVWDOODWLRQ JXLGH Engage the reverse gear for the reverse signal function test. ) 7, , + 09, *;065 P $!P The arrows under 09, *;065 must change direction on engaging the reverse gear. VVV P When using the GPS for the first time, the vehicle must be parked outdoors, while ensuring that it has a clear view in all directions (not in the immediate vicinity of buildings). Information on the GPS reception is given in the right-hand part of the display. Four different messages may appear: - : GPS reception is already available. - " : If this message is displayed, please contact the hotline. 7, , + 09, *;065 P P P VMN 7, , + 09, *;065 P $! 09, *;065 " 7, , + VMN 7, , + ) You must wait until , P (or P ) and P (or a higher value) is displayed. This procedure (first reception of the necessary GPS data) may take a few minutes. The unit must remain switched on for the entire duration of this procedure. If after 5 minutes there has been no change in the values, the parked position (clear view in all directions as far as possible) or the installation location of the 35 VMN Subject to correction and technical modifications Copyright by Becker GmbH, D-76303 Karlsbad , QVWDOODWLRQ JXLGH GPS antenna must be checked. However: a lower accuracy of the GPS signal (2-D FIX) does not lead to a poorer calibration, but instead will mean that the time and distance needed for the calibration will increase. Subject to correction and technical modifications 37 Copyright by Becker GmbH, D-76303 Karlsbad , QVWDOODWLRQ JXLGH If, even after a relatively long period of time, the display with the request !does not appear, then you should check the GPS reception conditions again (as under Service Mode in the Section "Function test of GPS antenna ( )" on page 40). appears, the calibration ride can be started. ) A calibration ride can also be performed in a non-digitised area. The insertion of the Navigation CD is not absolutely necessary after the navigation software has been installed. Without the Navigation CD inserted, no location is displayed. The basic requirement for a calibration ride is: GULYLQJ PHWUHV LQ D VWUDLJKW OLQH WKHQ WXUQLQJ E\ DW OHDVW GHJUHHV DQG WKHQ GULYLQJ PHWUHV LQ D VWUDLJKW OLQH DJDLQ DQG WXUQLQJ DJDLQ ) The direction you turn is of no significance. If these conditions cannot be fulfilled due to the road or the fact that you do not always have optimum GPS reception, this will not lead to a poorer calibration, but will simply mean the time and distance necessary for the calibration ride will be longer. Subject to correction and technical modifications 38 Copyright by Becker GmbH, D-76303 Karlsbad , QVWDOODWLRQ JXLGH ) If the unit is switched off during the calibration ride, language installation is requested when the unit is switched on again. Reinstallation can be skipped by pressing the 1DY button. !Y & Calibration has been completed successfully if the main navigation menu is displayed. For correct navigation on routes with time-dependent traffic guidance, the time should be set correctly as described under "System settings" in the operation guide.   YYY 6HUYLFH 0RGH In Service Mode, various functions can be checked in detail and the calibration can be modified. If the unit has already been calibrated, select the main navigation menu by pressing the 1DY button. If the unit has not been calibrated, proceed as described in the next point but one. [. . . ] )XQFWLRQ WHVW RI WKH *$/ VLJQDO UHYHUVH VLJQDO LQWHUQDO VHQVRUV  In the Service Mode, select using the right rotary control and press to confirm. Move the vehicle several metres forwards or backwards for the GAL signal function test. !    " !The number after $P should not increase if idling or pressing the accelerator when the vehicle is parked. $P &P %P S  #YP &P S Subject to correction and technical modifications 44 Copyright by Becker GmbH, D-76303 Karlsbad , QVWDOODWLRQ JXLGH Engage the reverse gear for the reverse signal function test. ) The number after #YP should jump from to ( to ). Drive round a bend to test the function of the internal sensors. ) The values after %P and &P should change. 1DY In order to quit the sensor test, press the back to the Service Mode. button. By pressing the right rotary control , the announcement can be repeated. [. . . ]