User manual CANDY CDI 4015
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANDY CDI 4015. We hope that this CANDY CDI 4015 user guide will be useful to you.
You may also download the following manuals related to this product:
CANDY CDI 4015 DATASHEET (662 ko)
Manual abstract: user guide CANDY CDI 4015
Detailed instructions for use are in the User's Guide.
[. . . ] The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. "START" programme button "SALT EMPTY" light "RINSE AID EMPTY" light Programme guide "ON/OFF" button For service and repairs call your local engineer on our national telephone number: EN 50242 place load Capacity with pans and dishes Water supply pressure Fuse Power input Supply voltage Description of the controls Technical data Operating the programmes and special functions The Waterblock system Water softener unit Programme selection 12 IMPORTANT All options MUST be turned on or off, BEFORE pressing "START" button. The dishwasher is equipped with a dirt sensor, able to analyse water murkiness during all "AUTOMATIC" program phases (see program list); thanks to this sensor the washing cycle parameters are automatically adapted to the real quantity of dirt on dishes. Thus excellent washing results are guaranteed while optimising water and energy consumption. [. . . ] By using this option, the strength of the selected cycle will be increased, adding one rinse and increasing the temperature of the water in the washing phase where foreseen. This option is recommended for very dirty dishes or when dirty dishes may not have been pre-treated allowing the soiling to dry up. "1/2 FLEXI" button To ensure that your dishwasher meets all your requirements, this button allows you to select: 1) Half Load Top Basket By selecting this option dishes are washed in the top basket and cutlery in lower basket. Half Load Lower Basket By selecting this option dishes are washed in the lower basket only. Before starting a new programme, you should check that there is still detergent in the dispenser. If there is any break in the power supply while the dishwasher is operating, a special memory stores the selected programme and, when the power is restored, it continues where it left off (if it is necessary, the appliance will make a short thermal anti-shock programme before). If you open the door during the drying cycle, an audible audio signal advises you that the drying cycle has not yet completed. A 5 second buzzer will sound (if not muted) 3 times at 30 second intervals to signal that the program has ended. Dishes can now be removed and the dishwasher turned off by pressing the "ON/OFF" button or dishes can be loaded for a new cycle. "DELAY START" button Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. proceed as follows to set a delayed start: Press the "DELAY START" button ("00" will appear on the display). Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). If you wish to see which programme has been selected, press the "PROGRAMME SELECTION" button. Proceed as follows to cancel a delayed start: Hold the "START" button down for at least 5 seconds. At this point, a new program and option buttons must be set to start a new program as indicated in the "PROGRAM SETTINGS" section. The buzzer may be muted as follows: With the dishwasher off, hold down the "PROGRAMME SELECTION" button for few seconds while simultaneously pushing the "ON/OFF" button. To turn the buzzer on again, follow the same procedure ("b1" will appear on the display to indicate that the buzzer is on). To ensure the correct operation of the anti-overflow safety device, it is recommended not to move or to tilt the dishwasher during operation. If it is necessary to move or to tilt the dishwasher, first make sure the washing cycle is finished and that no water is left in the tank. The waterblock system has been designed to improve the safety of your appliance, particularly when the machine is left unattended. The waterblock system actually prevents flooding which might be caused by a machine malfunction or as a result of a fracture on the pipes. How does waterblock work The sump located in the base of the appliance collects any possible water leakage and operates a sensor which subsequently activates a valve placed under the water tap and stops any water from the supply even with the tap fully opened. [. . . ] With cold water (15°C)** -Tolerance ± 10%Hot rinse with rinse aid Wash with prewash If setting the INTENSIVE wash programme, a second dose of about 20 g of detergent (1 table-spoon) must be added directly in the machine. ("RECOMMENDED" PROGRAMME) Once a day - for normal soiled pans and any other items that have been left all day for washing. Once a day - for heavily soiled pans and any other items that have been left all day for washing. Suitable for heavily soiled items that are to be washed straight after a meal (Max 8 place load). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CANDY CDI 4015
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANDY CDI 4015 will begin.