User manual CANDY CDPM 3T62PRDFX

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANDY CDPM 3T62PRDFX. We hope that this CANDY CDPM 3T62PRDFX user guide will be useful to you.


CANDY CDPM 3T62PRDFX : Download the complete user guide (1188 Ko)

Manual abstract: user guide CANDY CDPM 3T62PRDFX

Detailed instructions for use are in the User's Guide.

[. . . ] The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. For service and repairs call your local engineer on our national telephone number: EN 50242 place load Capacity with pans and dishes Water supply pressure (MPa) Fuse / Power input / Supply voltage Power consumption of the off-mode and of the left-on mode: 0, 45 W / 0, 45 W *Values are measured in a laboratory according to European Standard EN 50242 (consumption may vary according to conditions of usage). IMPORTANT The "intermittent" working of the washing pump MUST NOT BE considered a malfunction, it is a characteristic of the impulse washing so must be considered a normal function of the programme. Choose a programme by pressing the "PROGRAMME SELECTION" button. [. . . ] Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. The alarm for the programme end may be muted as follows: Press the "DELAY START" button ("00" will appear on the display). Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). The display will show the time remaining to the begin of the programme. At the end of the countdown, the programme will automatically start and the length of the selected cycle will be shown in the display. IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound). Keep the "PROGRAMME SELECTION" button pressed for at least 15 seconds (during this time 2 audible signals will sound). Release the button when the second audible signal sounds ("b1" will appear on the display to indicate that the alarm is on). "00" will appear on the display and some audible signals will sound. Press the same button again ("b0" will appear on the display to indicate that the alarm is off). Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. To turn the alarm on again, follow the same Memorization of the last programme used The last programme used can be memorized by following the below: Press the same button again ("A1" will appear on the display to indicate that the memorization is on). Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound). Keep the "PROGRAMME SELECTION" button pressed for at least 30 seconds (during this time, 3 audible signals will sound). Release the button when the THIRD audible signal sounds ("A0 " will appear on the display to indicate that the memorization is off). IMPORTANT This dishwasher is equipped with an anti-overflow safety device which will automatically discharge any excess water should a problem occur. To ensure the correct operation of the anti-overflow safety device, we recommend that the dishwasher is not moved or tilted during operation. If however it is necessary to tilt or move the dishwasher, please ensure that the washing cycle is complete and that there is no remaining water inside the dishwasher. Check if the drain tube is bent or if the siphon or filters are clogged. [. . . ] Keep the "PROGRAMME SELECTION" button pressed for at least 5 seconds, UNTIL an audible signal sounds. The current water softener setting level will be shown on the display. Press the same button again to select the required water softener level: each time the button is pressed, the setting will increase by one level. When you have reached "d7", the display will go back to "d0". [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CANDY CDPM 3T62PRDFX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANDY CDPM 3T62PRDFX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.