User manual CANDY CE 650 T
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANDY CE 650 T. We hope that this CANDY CE 650 T user guide will be useful to you.
Manual abstract: user guide CANDY CE 650 T
Detailed instructions for use are in the User's Guide.
[. . . ] , Please read this booklet carefully as it provides important guide lines for safe installation, use and maintenance and some useful advise for best results when using your washing machine. When contacting Candy or a Customer Services Centre always refer to the Model, No. On delivery, check that the following are included with the machine: Check that the machine has not incurred damage during transport. The appliance is supplied with a guarantee certificate which allows free use of the Technical Assistance Service. [. . . ] The final part of a washer dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged. WARNING: Never stop a washer dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. CHANGING THE SETTINGS AFTER THE PROGRAMMES HAS STARTED (PAUSE) Press and hold the "START/PAUSE" button for about 2 seconds, the flashing lights on the options buttons and time remaining indicator will show that the machine has been paused, adjust as required and press the "START/PAUSE" button again to cancel the flashing lights. If you wish to add or remove items during washing, wait 2 minutes until the safety device unlocks the door. When you have carried out the manoeuvre, close the door, press START button and the appliance will continue working where it left off. EN DOOR LOCKED INDICATOR The "Door Locked" indicator light is illuminated when the door is fully closed and the machine is ON. When START is pressed on the machine with the door closed the indicator will flash momentarily and then illuminate. A special safety device prevents the door from being opened immediately after the end of the cycle. Wait for 2 minutes after the wash cycle has finished and the Door Locked light has gone out before opening the door. EN "DIGITAL" DISPLAY The display's indicator system allows you to be constantly informed about the status of the machine: 1) WASH TEMPERATURE When a programme is selected the relevant indicator will light up to show the recommended wash temperature. The Temperature button can be used to decrease or increase the temperature of your chosen wash cycle. The programme has a temperature of 30°C and concludes with 3 rinses and a slow spin. SPECIAL "RINSE" PROGRAMME This programme carries out three rinses with a intermediate spin (which can be reduced or excluded by using the correct button). This program can be also used as cycle of Bleaching (see table of washing cycle programmes). SPECIAL "FAST SPIN" PROGRAMME Programme "FAST SPIN" carries out a maximum spin (which can be reduced by using the correct button). The "Mix & Wash" programme has a temperature of 40°C and alternate dynamic phases (the basket that turns) to static phases (fabrics in soak in phase of rest) with a duration programme that almost reaching the 2 hours. The first washing of new coloureds fabrics must be done separately; · In every case, never mix NON-FAST COLOUREDS fabrics. This programme is particularly suited to slightly dirty cottons and mixed fabrics. Using the Degree of soiling button on the Rapid cycle will enable you to select either a 14, 30 or 44 minute wash cycle. When selecting the rapid programme, please note that we recommend you use only 20% of the recommended quantities shown on the detergent pack. The main wash and the rinse gives best results thanks to the rotation rhythms of the drum and to the water levels. The programme has a maximum temperature of 40°C and concludes with 3 rinses and a short spin. [. . . ] EN If you wish to select a timed drying cycle, press the "drying programme selection" button until the required time indicator lights up. The programme carries out with the programme selector stationary on the selected programme till cycle ends. The drying programme indicator will be on until the cool down phase will begin and the indicator ( ) will go on. at the end of the programme the word "END" will appear on the display. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CANDY CE 650 T
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANDY CE 650 T will begin.