Detailed instructions for use are in the User's Guide.
[. . . ] 02494
YTH1342XP
Owner's Manual
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
I. GENERAL OPERATION
⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠⢠Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. [. . . ] ⢠The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position. ⢠When the engine is running, any attempt by the operator to leave the seat without ï¬rst setting the parking brake should shut off the engine. ⢠When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. ⢠The attachment clutch should never operate unless the operator is in the seat.
BLADE CARE
For best results mower blades must be kept sharp. Replace bent or damaged blades.
5/8" BOLT OR PIN
BLADE
BLADE REMOVAL (See Fig. 12)
⢠⢠⢠Raise mower to highest position to allow access to blades. Remove blade bolt, lock washer and ï¬at washer securing blade. Install new or resharpened blade with trailing edge up towards deck as shown.
FIG. 13
BATTERY
Your tractor has a battery charging system which is sufï¬cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. NOTE: The original equipment battery on your tractor is maintenance free. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to âleakâ power.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.
⢠â¢
Reassemble blade bolt, lock washer and ï¬at washer in exact order as shown. torque).
IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.
16
MAINTENANCE
⢠⢠⢠⢠⢠⢠Remove terminal guard. Disconnect BLACK battery cable ï¬rst then RED battery cable and remove battery from tractor. Reinstall battery (See âREPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). ⢠Remove yellow cap from bottom ï¬tting of drain valve and install the drain tube onto the ï¬tting.
OIL DRAIN VALVE
V-BELTS
Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear.
TRANSAXLE COOLING
The transmission fan and cooling ï¬ns should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. ⢠Inspect cooling fan to be sure fan blades are intact and clean. ⢠Inspect cooling ï¬ns for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling ï¬ns.
CLOSED AND LOCKED POSITION
YELLOW CAP
DRAIN TUBE
FIG. [. . . ] 3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds) 2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipmentâzero turn riders, wide area walks, and ground engaging commercial equipment. 2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors, walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated. Emission control system components necessary to comply with CARB-TIER-II and EPA regulations, except for those components which are part of engine systems manufactured by third party engine manufacturers for which the purchaser has received a separate warranty with product information supplied at time of purchase. 1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional, non-institutional or non-income producing use. [. . . ]