User manual JONSERED 370

[. . . ] no Do ect to dam or subjked crac OW N E R S M A N U A L M o d e l N o . CL36A 36 Inch Mower Grass Catcher Assembly Operation Customer Responsibilities Service and Adjustments Repair Parts 532175732 PRINTED IN U. S. A. 1 10. 12. 00 rad 954 12 00-93 SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION · · · · · · · · · · · · · · · · Read, understand, and follow all instructions in the manual and on the machine before starting. [. . . ] 12 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 REPAIR PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . center of manual 3 KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tractor and while mowing. We recommend wide vision safety mask for over the spectacles or standard safety glasses. UNPACKING INSTRUCTIONS · · Remove all parts and packing materials from carton. Fold flaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. Be sure all parts are there. CARTON CONTENTS: (2) Container Tops (2) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Mounting Bracket (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual · NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE GROUP "A" REAR MOUNTING BRACKET TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping (4) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 GROUP "B" SUPPORT POST TO CONTAINER SUPPORT (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 GROUP "C" SUPPORT POST TO MOUNTING BRACKET (1) Bracket Support Pin (1) Retainer Spring (3) Tubing End Caps 4 BAG OF PARTS CONTENTS (continued) GROUP "D" (2) Latch Hook Assembly LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Nut, Weld #10 GROUP "E" CHUTE LATCH ASSEMBLY TO UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "F " CHUTE LATCH ASSEMBLY TO LOWER CHUTE (1) Rubber Latch (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 5 ASSEMBLY PARTS IDENTIFICATION COVER ASSEMBLY UPPER CHUTE DUMP BAG INDICATOR r is ne ntai en d. Coe wh r. NOTE: Right container should always overlap left container at center support. · Close cover and lock latch handle over center support tube. COVER LATCH HANDLE CONTAINER WARNING AD INR n o s to GtNepo tcejbuc r e a ot c ar o m e w dek re w a ra ro lnu dn ad se ed a m c s eit . yl n rp eh a p o k c o c er lr e a b si y r f g m m tsn uqe dne ell a lt n e r d e C. d R . y alpe no iat calpeemec en si r h w e o c t n s n e i at n n . re 7 · · · · · · LOWER CHUTE (See Figs. 7A & 7B) Use Hardware - - GROUP "D" Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw, flat washer, and lock washer as shown. Place front of chute over front of mower deck opening and slide into place as shown. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. W CONTAINER HANDLE CENTER SUPPORT TUBE CONTAINER WARNING is er is er ntain ed. Co when ce iner. r unles a recom riorat ING mowe RN te detie only ARN and Use WA opera ged. not wear Do ct to dama or subjeed crack WASHER LOCK WASHER LATCH FIG. 6 DEFLECTOR SHIELD LATCH WELD NUT WELD NUT LOCK WASHER WASHER SCREW FIG. 7B 9 ASSEMBLY 8 · · · CHUTE LATCH ASSEMBLY (See Fig. 8) Use Hardware - - GROUPS "E & F" ALIGNMENT SLOT Assemble latch pin to upper chute, as shown. [. . . ] Care should be taken not to damage the parts and that the ball moves freely at the beginning of each use. If the grass catcher fails to pick up cut grass or leaves, it is an indication that clogging has occurred in the system or that the grass catcher containers are full. Disengage blades, shift into neutral, engage the parking brake and stop the engine. CAUTION · Do not operate mower with grass catcher partially installed. [. . . ]