User manual JONSERED 455

[. . . ] 2 MH Printed in U. S. A. SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. · · · · · · · · · · · · · · · GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. [. . . ] Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tractor and while mowing. We recommend a wide vision safety mask for over the spectacles or standard safety glasses. UNPACKING INSTRUCTIONS · · Remove all parts and packing materials from carton. Fold flaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Mounting Bracket (1) Mounting Support Plate (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual · NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE GROUP "A" REAR MOUNTING BRACKET AND SUPPORT PLATE TO DRAW BAR (6) Bolt 7/16 - 14 x 3/4 Self Tapping GROUP "B" SUPPORT POSTS TO COVER ASSEMBLY (2) Bolt 5/16 - 18 x 2-1/4 (2) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 4 BAG OF PARTS CONTENTS (continued) GROUP "C" SUPPORT POSTS TO MOUNTING BRACKET (2) Retainer Spring (2) Support Clevis Pin (4) Tubing End Caps GROUP "D" LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Latch Hook Assembly (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Nut, Weld #10 GROUP "E" CHUTE LATCH ASSEMBLY to UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "F " (1) Rubber Latch CHUTE LATCH ASSEMBLY to LOWER CHUTE (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 5 ASSEMBLY PARTS IDENTIFICATION COVER UPPER CHUTE r is ne ntai en d. Coe wh r. Re cont erlyi ently ent prop qu em r is g frereplac aine k ba d cont Checmende less tion. com un ra re er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. 6) No hardware required NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting assembly to tractor. With cover closed, lift assembly and place support posts into mounting bracket. Line up holes in mounting bracket with holes in support posts and insert support post clevis pins. Tap each end cap onto container support tubes to seat securely. Place bottom half inside of top half, as shown. Place one foot inside bottom half and lift top half to meet bottom half. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. · Repeat for second container. CONTAINER BOTTOM HALF COVER ASSEMBLY CONTAINER TOP HALF CONTAINER BOTTOM HALF END CAP SUPPORT POST CLEVIS PINS PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF LOCKING TAB ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. RETAINER SPRINGS SUPPORT POST MOUNTING BRACKET er tain on hen d. C w r. R t co erly ently en prop qu acem r is g fre pl ne ba d re ntai ck de co Che men less n. 11 &12) No hardware required Assemble hardware shown (latch pin) to upper chute. Press weld nut into rubber latch and assemble rubber latch to lower chute, as shown. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bagger indicator. [. . . ] Remove one container at a time by grasping container handles and pulling toward the rear, off of the tube rails. With the container resting on the ground, close and secure the top of the plastic lawn bag. Tip the container on its side and slide the filled bag from the container. Install a new plastic lawn bag with the edges of the bag draped over upper lip of the Container (for replacement bags refer to REPLACEMENT PARTS). [. . . ]