User manual KAWAI SR70

[. . . ] 13 6. 2 Quit " SETUP " menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6. 3 Rinsing temperature setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6. 4 Washing temperature setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6. 5 Rinse aid dispensing setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. The internal pipes of the detergent and rinse aid pumps should be replaced by the AfterSales Service every 12 months or 15, 000 wash cycles and operation of the diaphragm rinse aid pump should be checked. 6 SET-UP Setup During first startup, the functions/parameters listed below must be set or adjusted: 6. 1 Dishwasher parameter modification procedure: Only accessible after filling is complete or with the hood open. Access "programming mode" by pressing the button for a few seconds with the appliance on with the hood open and the tank empty (after the filling and heating phases). The display shows UnLo1:58; when the beep sounds, release the button and press it again at once. Keep pressing the button again to scroll through all the modifiable parameters in the following order: Rinsing temperature (boiler temperature) 13 CW 620/630 Washing temperature (tank temperature) Quantity of rinse aid dispensed, OPT, only if installed (the number indicates the number of seconds for which the peristaltic pump is operated) Quantity of detergent dispensed, OPT, only if installed (the number indicates the number of seconds for which the peristaltic pump is operated) Starton/startoff Set at "on" to start the cycle when the hood is closed. Set at "off" for cycle start after confirmation with the start button Water hardness setting (OPT, on models with softener only) tStP on/off "on" = minimum rinsing temperature as set, regardless of intake water temperature; the cycle duration may be a few seconds longer than the nominal length. "off" = the minimum rinsing temperature might be a few degrees lower than the setting if hot intake water is not used. 14 CW 620/630 Rinse aid pump total operating minutes display. Energy consumption (kW) display The Pc option indicates the total kW consumed since installation of the dishwasher or since the latest reset. Display of the number of cycles performed When scrolling through the appliance parameters, the "tc 88888" item will also appear; this is the count of the total cycles performed by the dishwasher since installation. 19 CW 620/630 6. 12 Energy consumption ­ Display and reset if required To reset, press for 3 seconds. The duration of program P4 can be customised from 3 to 10 minutes Access the programming procedure and scroll through to "inF" using the press the minutes) button, then scroll through to 03:00 and button to set the time required (from 3 to 10 After a few seconds without the user pressing any buttons, the display will return to the normal operating status and the modifications will be saved. 6. 14 Steam extraction time setting (optional if installed) Steam extraction system operating time display and setting 20 CW 620/630 6. 15 Service setting (for AfterSales Service only) See information on Smegtech 6. 16 Starting the peristaltic pumps ­ rapid filling of detergent and rinse aid delivery circuit. Perform after the parameter modification procedure explained in the previous point. With the dishwasher powered up, access "programming mode" by pressing the on/off button for a few seconds; at the "beep", release the button and press it again quickly within 0. 5 seconds. The peristaltic pumps continue to operate until the same button is pressed again. The rinse aid and detergent symbol lights remain on as long as the pumps are on; bear in mind that the rinse aid peristaltic pump fills the circuit in about 7 minutes, while for the detergent it only takes 2 minutes. 21 CW 620/630 7 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) The dishwasher is able to identify a number of malfunctions and show them on the display. If the problem persists after the dishwasher has been switched off and back on, proceed as described below: The antiflooding system has been Err01 activated (for the relevant models only). Err04 Tank temperature probe malfunction Large water leak: check the origin of the problem. The tank does not fill within the allowed time: check water intake tap, dynamic pressure in intake system, cleaning of water intake filter, possible damage to water intake hose or cleaning of rinsing nozzles. [. . . ] Plates/glasses badly arranged Low washing temperature Check type and quantity of detergent. Pipe inside detergent and/or rinse aid peristaltic pump worn or broke, have it replaced by the AfterSales Service. Check temperature shown on the display, call the aftersales service if less than 50 Increase washing duration, especially if dishes are very dirty or dirt has dried on. Check that nozzles are clean, and ensure that the softener is working properly (if installed). [. . . ]