User manual PEG PEREGO PRIMO VIAGGIO SL

[. . . ] • The assembly and installation operations must be conducted by adults. Product characteristics WARNING • Avoid inserting fingers into the mechanisms. € Install this group 0+ car safety seat facing opposite to the normal forward movement of the vehicle. € Death or serious injury can result if this car safety seat is installed on seats with airbags. [. . . ] Some parts might heat up and be harmful to the delicate skin of the child -check before placing the child in the seat. € Do not use the safety seat without its fabric covering, which cannot be replaced with one not approved by the manufacturer since it is an integral part of the safety seat and the safety system. € If in doubt refer to the manufacturer or retailer of the safety seat. € Do not remove the adhesive and stitched labels since this might make the product non compliant with legal requirements. € Do not use the safety seat if it has signs of breakage or missing parts, is second hand, or if it has been subjected to violent stress in an accident, because it might have suffered extremely dangerous structural damage. € For any repairs, replacement parts and information about the product, contact the after-sales assistance service. € Do not use this car safety seat after five years from the date of production indicated on the structure. The natural ageing of the materials may mean that it is no longer compliant with standards. € The use of the safety seat for premature infants born at less than 37 weeks could cause respiration problems for the infant seated in the safety seat. € Do not use accessories not approved by the manufacturer or by the competent authorities. € To avoid the risk of falling, never place the safety seat on raised surfaces (tables, work surfaces) soft surfaces (beds, sofas) or sloping surfaces. € In the home do not use the car safety seat if the child is able to remain seated alone. Instructions for use 1• "Primo Viaggio tri-fix" is provided with the Ganciomatic System for in-car attachment and detachment from an "Isofix Base" or "Adjustable Base" and outside the vehicle to Peg-Pérego strollers and chassis. To attach "Primo Viaggio tri-fix" (to an "Isofix Base", "Adjustable Base", or Peg-Pérego stroller or chassis) align it with the attachment points and push down with both hands until it clicks into place. 2• To release "Primo Viaggio tri-fix" (from an "Isofix Base", "Adjustable Base", or Peg-Pérego stroller or chassis) raise the handle to the transport position, push the lever on the backrest upwards and at the same time raise the safety seat. 3• To engage the safety harness, put the two shoulder straps on and insert them into the buckle of the crotch strap until they click into place. 4• To release the safety harness press the red button on the crotch strap buckle. 5• To slacken the harness shoulder straps press the metal button in the centre of the safety seat and simultaneously pull the shoulder straps towards you. 6• To tighten the shoulder straps on the child, pull the central adjustment strap towards you as shown in the figure, taking care not to over-tighten the straps and leaving minimal room to manoeuvre. 7• The shoulder straps of the safety harness and the “Side Impact Protection” headrest can be adjusted simultaneously to 5 different heights so as to follow the growth of the child. To adjust the height, press the rear height adjustment button (on the safety seat backrest) and at the same time raise or lower to the required position, ensuring that it clicks into place. Slacken the shoulder straps before adjusting the height of the safety harness and the headrest. [. . . ] 19• To remove the padding: • slide off the four padding fixing tabs from the edge of the safety seat; • remove the two side guide covers for the car seat belt; • remove the metal button cover in the centre of the safety seat, releasing it from under the seat; • remove the padding. Padding cleaning instructions Cover removal 20• To refit the padding: • slide on the padding; • insert the four padding fixing wings on the edge of the safety seat; • reposition the metal button cover in the centre of the safety chair and engage it from under the chair; • position the two side guide covers for the car seat belt with the slots facing the inside of the safety seat and check that they are correctly engaged in position. 21• To refit the headrest and cover: • from the back of the safety seat insert the headrest height Refitting adjuster in the lowest hole and from the front align and engage the headrest with this, ensuring that the teeth are correctly engaged with the headrest. 22• To refit the safety harness: • IMPORTANT: make sure the straps are not twisted. [. . . ]