User manual ROSE DISPLAYS ANOGOTCHA STAND TELESCOPING

[. . . ] AnoGotcha Stand TM Parts Read this instruction sheet carefully before assembly. Make sure all parts are accounted for before discarding any packaging materials. [. . . ] Part #02INSTeleAnoGotchaStand Incept-12. 09. 02 35 Congress Street, Salem, MA 01970 Tel# 1-800-631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 3 · Slide one T-Gotcha holder into each AnoGotcha shell. · Attach one shaped end cap onto each end of both AnoGotcha shells. Telescoping assembly continued Insert T-Gotcha holders into AnoGotcha shells. shaped end cap AnoGotcha shell T-Gotcha Slide T-Gotcha holder into each AnoGotcha shell as shown. Attach one shaped end cap onto each end of AnoGotcha holders, as shown. You should now have two AnoGotcha holders with one shaped end cap on each end. Step 4 Attach top AnoGotcha holder onto vertical poles. · Slide one threaded rod with ball knob through top hole in one vertical pole. · Slide threaded rod completely through top channel of one AnoGotcha holder and through top hole of second vertical pole. Tighten securely. ball knobs top AnoGotcha holder 11" round base Slide threaded rod through the top hole of one vertical pole and then through top channel of one AnoGotcha holder. Screw ball knob tightly onto threaded rod. vertical pole Your stand should now look like this. AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSTeleAnoGotchaStand Incept-12. 09. 02 35 Congress Street, Salem, MA 01970 Tel# 1-800-631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 5 · Choose hole that matches appropriate graphic distance from floor. · Slide one threaded rod with ball knob through appropriate hole in one vertical pole and through bottom channel of one AnoGotcha holder. 14" Telescoping assembly continued Attach bottom AnoGotcha holder to vertical poles. Be sure locks are facing same direction. · Slide through corresponding hole of second vertical pole. Note: Make sure the hinge on the bottom T-Gotcha faces up and in the same direction as the hinge on the T-Gotcha at the top of the stand. Tighten securely. 14" 8" 2" Numbers represent distance from floor. T-Gotcha hinge must face up and in the same direction as top T-Gotcha. 8" 2" Slide threaded rod through appropriate hole and through bottom channel of remaining AnoGotcha holder. AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSTeleAnoGotchaStand Incept-12. 09. 02 Slide threaded rod through matching hole on opposite vertical pole. Attach ball knob, tighten securely. 35 Congress Street, Salem, MA 01970 Tel# 1-800-631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 6 · Snap open top AnoGotcha holder completely. [. . . ] Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSTeleAnoGotchaStand Incept-12. 09. 02 Your completed Telescoping AnoGotcha Stand should look similar to this. 35 Congress Street, Salem, MA 01970 Tel# 1-800-631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com [. . . ]