User manual SHARP CD-C607H
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP CD-C607H. We hope that this SHARP CD-C607H user guide will be useful to you.
You may also download the following manuals related to this product:
SHARP CD-C607H (1285 ko)
SHARP CD-C607H (1258 ko)
SHARP CD-C607H (1166 ko)
SHARP CD-C607H (1272 ko)
SHARP CD-C607H (1108 ko)
SHARP CD-C607H (1215 ko)
SHARP CD-C607H (3095 ko)
SHARP CD-C607H (1258 ko)
Manual abstract: user guide SHARP CD-C607H
Detailed instructions for use are in the User's Guide.
[. . . ] Wenn die ON/STAND-BY-Taste auf STAND-BY eingestellt wird, kann das Gert unter Verwendung der Timer-Betriebsart oder Fernbedienung in Betrieb gesetzt werden. Warnung: In diesem Gert sind keine vom Benutzer wartbaren Teile vorhanden. Vor Ausfhrung von irgendwelchen Kundendienstarbeiten oder bei lngerer Nichtverwendung des Gertes stets den Netzstecker aus der Netzsteckdose ziehen. Lorsque la touche ON/STAND-BY est mise en STAND-BY, l'appareil est toujours sous tension. [. . . ] This unit should only be used within the range of 5C 35C (41F - 95F). The apparatus is designed for use in moderate climates.
The sound level at a given volume setting depends on speaker efficiency, location and various other factors. Excessive sound pressure from earphones and headphones can cause hearing loss.
E-2
Controls and indicators
1 Front panel
2
MINI COMPONENT SYSTEM
CD-DH790
3 4 5
FUNCTION ON/STAND-BY
9 10 11 12 13
PUSH OPEN
VOL
AUDIO IN
6 7 8
14
PHONES
Page 1. 15
1
2
3
4 5 6 7 8 9 10
Display
16 17 11 18 19
12 1314
15
Page 1. 10
E-3
Controls and indicators (continued)
1 24 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Remote control
CD USB
25 26 27 28 29 30 31 32 33 34
TAPE
35 36 37 38 39
Page 1. Speaker Wire
1 2
3
4
E-4
System connections
Make sure to unplug the AC power lead before making any connections. TV
AM loop aerial Installing the AM loop aerial < Assembling >
To video input socket Video cable (not supplied)
< Attaching to the wall >
wall
screws (not supplied)
FM aerial Right speaker
Left speaker
Red Black Wall socket (AC 220 - 240 V ~ 50/60 Hz)
Aerial connection
Demonstration mode
Supplied FM aerial: Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the direction where the strongest signal can be received. External FM aerial: Use an external FM aerial (75 ohms coaxial cable) for better reception. When an external FM aerial is used, disconnect the supplied FM aerial wire. Supplied AM loop aerial: Connect the AM loop aerial to the AM and GND terminals. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Keep the remote control away from moisture, heat, shock, and vibrations.
To turn the power on
Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode.
Display brightness control
To dim the display brightness, hold down the CLEAR/ DIMMER button on the remote control for 2 seconds or more.
Volume auto fade-in
If you turn off and on the main unit with the volume set to 27 or higher, the volume starts at 16 and fades in to the last set level.
Volume control
Turn the volume knob towards VOL +/ (on main unit) or press VOLUME +/ (on remote control) to increase or decrease the volume.
X-Bass control
Test of the remote control
Check the remote control after checking all the connections. The remote control can be used within the range shown below: Remote sensor
MINI COMPONENT SYSTEM
CD-DH790
When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS button on the remote control.
Bass control 1 Press the BASS/TREBLE button to select "BASS". 2 Within 5 seconds, press the VOLUME (+ or ) button to
adjust the bass.
Treble control 1 Press the BASS/TREBLE button to select "TREBLE". 2 Within 5 seconds, press the VOLUME (+ or ) button to
FUNCTION
ON/STAND-BY
adjust the treble.
0. 2 m - 6 m (8" - 20')
AUDIO IN PHONES
VOL
PUSH OPEN
Equaliser
When the EQUALIZER MODE button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER MODE button repeatedly until the desired sound mode appears.
FLAT GAME No equalization. CLASSIC For classical music.
POPS VOCAL
E-6
JAZZ
Setting the clock (Remote control only)
Listening to the iPod
Supported iPod models: iPod nano (software 1. 2 above) iPod mini (software 1. 2 above) iPod (5th generation) (software 1. 3 above) (Dock connector equipped Click Wheel model) iPod (4th generation) (software 3. 0. 2 above) (Dock connector equipped Click Wheel model) iPod nano (2nd generation) (software 1. 0. 0 above) iPod nano (3rd generation) (software 1. 0. 3 above) iPod nano (4th generation) (software 1. 0. 3 above) iPod classic (software 1. 0. 3 above) iPod touch (software 1. 1 above) iPod touch (2nd generation) (software 2. 1 above) Caution: Please update your iPod unit to the latest software version from Apple's homepage before using it. Notes: Once the iPod is connected to the unit it will begin charging. The iPod unit cannot be charged whilst the main unit is in the stand-by mode or during USB mode. Auto power on function: When you press any of the following buttons, the unit turns on. [. . . ] Excessive sound pressure from earphones and headphones can cause hearing loss. Be sure your headphones have a 3. 5 mm (1/8") diameter plug and impedance between 16 and 50 ohms. Adjust the volume using the VOLUME control.
Symptom Sound skipping. If a power failure occurs during playback, the heads remain engaged with the tape. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP CD-C607H
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP CD-C607H will begin.