User manual YAESU FL7000

[. . . ] 38 How to Skip (Omit) a Channel during Memory Scan Operation . . . . . . . . . . . . . . 40 Programmable (Band Limit) Memory Scan (PMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 "Priority Channel" Scanning (Dual Watch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Automatic Lamp Illumination on Scan Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Now, press and hold in the [MR/MW(SKIP)] key for one second to initiate Programmable (Band Limit) Memory Scan. 10 pairs of Band Limit memories, labeled L1/U1 through L10/U10 are available. You therefore can set upper and lower operation limits in multiple segments on the band, if you like. FL7000 OPERATING MANUAL 41 SCANNING "PRIORITY CHANNEL" SCANNING (DUAL WATCH) The FL7000's scanning features include a two-channel scanning capability which allows you to operate on a VFO or Memory channel, while periodically checking a user-defined Memory Channel for activity. If a station is received on the Memory Channel which is strong enough to open the Squelch, the scanner will pause on that station in accordance with the Scan-Resume mode set via Set Mode Item 32: RESUME. Here is the procedure for activating Priority Channel Dual Watch operation: VFO Priority 1. Recall the memory channel you wish to use as the "Priority" frequency. Press the [F/L] key, then press the [VFO(PRI)] key to activate the VFO Priority mode. The display will remain on the VFO frequency, but every five seconds the radio will check the Priority Channel (memory channel) for activity. Press [F/L] [VFO(PRI)] again to disable the VFO Priority mode. Memory Channel Priority 1. Store the frequency you wish to be the "Priority" Channel into memory channel "1. " 2. Press the [F/L] key, then press the [VFO(PRI)] key to activate the Memory Priority mode. Press the [F/L] key, then press the [0(SET)] key to enter the Set mode. Press the [F/L] key momentarily to enable adjustment of this Set Mode Item. When you have made your selection, press the PTT switch to save the setting and exit to normal operation. BAND EDGE BEEPER The FL7000 will automatically "beep" when a band edge is encountered during scanning (either in standard VFO scanning or during PMS operation). You may also enable this feature (band edge beeper) to operate when the frequency reaches the band edge while tuning using the DIAL knob. Press the [F/L] key, then press the [0(SET)] key to enter the Set mode. Press the [F/L] key momentarily to enable adjustment of this Set Mode Item. When you have made your selection, press the PTT switch to save the setting and exit to normal operation. 44 FL7000 OPERATING MANUAL SCANNING WEATHER ALERT SCAN This feature allows you to check the Weather Broadcast Memory Channels for the presence of the NOAA Alert Tone while operating using VFO scan or Memory channel scan. When the Weather Alert Scan feature is engaged, the FL7000 will check the Weather Broadcast Memory Channels for activity every five seconds while scanning. If you watch the display carefully, you'll observe the scanner periodically shifting to the Weather Broadcast bank, scanning the Weather channels quickly in search of the Alert Tone, after which regular scanning will resume for another five seconds. Press the [F/L] key, then press the [0(SET)] key to enter the Set mode. Press the [F/L] key momentarily to enable adjustment of this Set Mode Item. [. . . ] ONLY: The scanner will only scan channels that are flagged (Preferential Scan List). OFF: All memory channels will be scanned (the "flag" will be ignored). Set Mode Item 43 [SPLIT] Function: Enables/Disables split CTCSS/DCS coding. ON, " you will see the following additional parameters after the "DCS" parameter while configuring Set Mode Item 44: SQL. TYP. [. . . ]